How to Flash AM32 on BLHeli-32 ESC: Step-by-Step Guide (Bootloader and Firmware)

If your ESC already comes with AM32, you can configure or flash it using one of the AM32 configuration tools available. However, if your ESC has BLHeli_32, converting it to AM32 is a bit more complex. This step by step tutorial will guide you through the process.

Some of the links on this page are affiliate links. I receive a commission (at no extra cost to you) if you make a purchase after clicking on one of these affiliate links. This helps support the free content for the community on this website. Please read our Affiliate Link Policy for more information.

For more information about ESCs, check out this buyer’s guide:

Disclaimer: Official instructions are available on the AM32 homepage: This tutorial demonstrates how I personally flash my ESC. Follow these instructions at your own risk; I am not responsible for any damages. I recommend familiarizing with the process on a spare ESC that you don’t need, so if anything goes wrong you won’t be grounded.

Why Flash AM32?

A couple of reasons why you might want to switch from BLHeli32 to AM32:

However, if you find it too difficult to flash AM32, my personal suggestion is to stay on BLHeli32 and keep flying. There’s is really nothing wrong with BLHeli32, unless there’s a bug or new features you want to have by upgrading to AM32.

Or just buy ESC with AM32 pre-installed:

Process Summary

Here are the simple steps to flash AM32 onto a BLHeli_32 ESC:

  • Connect ESC to STLink V2 Programmer
  • Remove write protection and erase the chip
  • Install AM32 Bootloader on the ESC
  • Flash AM32 Firmware

Is Your ESC AM32 Compatible?

At the moment, not every BLHeli_32 ESC is compatible with AM32. Before proceeding, check if your ESC is compatible:

What You Need

ST-Link V2 Programmer, purchase here (under $10):

Stm32 St Link V2 Program Usb Tool Pinout 3.3v 5v Dio Clk

STM32 ST-Link Utility:

This software is needed for disabling write protection on the BLHeli_32 ESC, allowing you to install the AM32 bootloader. Alternatively, you can use STM32CubeProgrammer, which may require account registration to download.

Stm32 St Link Utility User Interface Home Screen

Multi_ESC Config Tool:–configuration-tool

This tool is used to flash AM32 firmware and configure the ESC using Betaflight passthrough, similar to BLHeli32Suite.

Am32 Configuration Multi Esc Config Tool Flash Firmware

Download AM32 Bootloader file here:

To determine which bootloader file is right your ESC, refer to the supported hardware list:

Example: For the Tekko32 4in1 ESC with the STM32 F051 processor, it’s listed under the target name FD6288, with the bootloader labeled PA2.

Am32 Esc Target Name Bootloader Firmware Compatiblity List Github Processor

Click on the required bootloader file, then select “View raw” to download it.

Stm32 St Link V2 Program Usb Tool Pinout 3.3v 5v Dio Clk

Download AM32 Firmware file here:

Ensure you get the correct firmware file for your ESC based on the target name and processor type. Incorrect firmware, the ESC simply won’t work (e.g., no response and makes three short beeps repeatedly when powered on). If you flashed the wrong firmware, you can still flash the correct one which should resolve these issues, at least that’s my experience.

Find the firmware file by target name and processor, then click the link to download.

Am32 Firmware Files Github Download

Once you have downloaded the two necessary files, you are ready to begin the flashing process.

Am32 Bootloader Firmware Files Tekko32 F051 Esc

How to Flash AM32 Bootloader

Connecting STLink Programmer to ESC

ESC Side ST-Link Tool

You need to find the tiny SWC and SWD pads on your ESC. Sometimes they are labelled which is easy to spot.

Esc Stm32 F051 Processor Swd Swc Pinout Pads Flash Bootlader Blheli32 Am32 Tekko32

The locations of these pads are similar across different ESCs, and you can tell them apart by following the traces.

Esc Stm32 F051 Processor Swd Swc Pinout Pads Flash Bootlader Blheli32 Am32

Stm32 St Link V2 Program Usb Tool Pinout 3.3v 5v Dio Clk

You also need to connect the ground (GND). You can use any GND on the ESC, including the XT60 GND.

Before connecting the STLink V2 tool to the ESC, ensure the ESC is powered by a LiPo battery or bench power supply via the XT60 connector.

Flash Blheli32 Esc Am32 Firmware Bootloader St Link V2 Programmer Wiring Connection

In the ST-Link Utility, click on “Target” in the top menu, then “Settings,” and change Mode to “Hot Plug.” Leave the rest at default.

Stm32 St Link Utility Settings Hot Plug Am32

Removing Write Protection and Erasing the Chip

Disclaimer: Once you erase the chip, you cannot flash BLHeli32 back onto the ESC.

Click on “Target” in the top menu, then select “Option Bytes.”

Flash Immersionrc Irc Ghost Rx Receiver Expresslrs Stm32 Stlink Utility Target Option Bytes

Change “Read Out Protection” to Level 0, and click on “Unselect all” under Flash sectors protection. Click “Apply.”

Stm32 St Link Utility Remove Read Write Protection Level 0 Unselect

You should see “Option Bytes Updated Successfully” in the console, indicating write protections have been removed.

Now, go to “Target,” then “Erase Chip” to erase BLHeli32 on the ESC. If you encounter an error, try “Erase Sectors” and select all as a workaround.

Stm32 St Link Utility Erase Chip Sector

Installing AM32 Bootloader

Open the bootloader file by clicking on “Binary File”.

Stm32 St Link Utility Program Binary File Am32 Bootloader

Under “Target”, click on “Program”.

Stm32 St Link Utility Program Binary File Menu

For F051 processors, ensure the Start address is 0x08000000. Select the bootloader file and check “Skip Flash Erase.”

Click “Start” to flash.

Stm32 St Link Utility Program Binary Fil3 Am32 Bootloader Skip Flash Erase

Removing SWC/SWD Wires

Once the bootloader is flashed, safely disconnect the ST-Link V2 tool and desolder the SWC, SWD, and GND wires from the ESC.

Flashing AM32

Once your ESC has the AM32 bootloader, it will be recognized by AM32 Configuration Tools, including the Multi_ESC config tool. There, you can flash the AM32 firmware and load the default settings via Betaflight passthrough.

Connect the ESC to your Betaflight flight controller and power the ESC.

Flash Esc Am32 Firmware Flight Controller Betaflight Passthrough

In Multi ESC Config Tool, select the COM port of your FC and click “Connect”.

Go to the “Flash” tab and click on one of the ESCs you want to flash (M1, M2, M3, or M4). It should say “Connected – No EEprom”.

Load the firmware we downloaded earlier, then click “Flash Firmware”.

Am32 Configuration Multi Esc Config Tool Flash Firmware Send Default Settings

Once done, click on “Send Default Settings” to write the EEPROM.

You should now have a functional AM32 ESC!

Testing ESC

You can test the ESC by soldering a motor to it and attempting to spin it in the Betaflight Motor tab. If all went well, the ESC should work normally.

Configuring AM32

There are multiple tools you can use to configure AM32 ESC, including

  • Multi ESC Config Tool (standalone tool)
  • (AM32 online tool – Chrome based)
  • (Bluejay online tool – Chrome based)

For freestyle FPV drones, the AM32 developers recommend:

  • Turn on Variable PWM frequency
  • Set Motor KV and Motor poles to match the motor
  • Leave the rest of the settings at default

I will provide a more detailed post on the different settings after further testing.


I hope you find this tutorial useful. Let me know if you have any questions. Happy flying!

Latest articles


Related articles

Leave a reply

Please enter your comment!
Please enter your name here